Peter’s Photos: Metalwork Photos

Metalwork Photos

2000-11-30 Lathe AL-60
01 Lathe 02 Front Panel 03 Top Panel
2001-03-12 Car Stuff
01 Seat Mold 02 Craig w:Grinder 03 Craig Grinding 04 Seat Mold 05 Nylon
06 Bushes
2001-04-14 Lathe Work
01 Lathe Work
2006-07-30 HAE-VH
01 HAE-VH Parts
2006-08-12 HAE-VH Crank
07 Crank Start 09 Lathe Trick 10 Faced and Turned
2006-08-12 Parting Tool
11 Parting Tool
2006-10-24 Crank
01 Crank
2006-11-28 Handwheel
01 Handwheel 02 Handwheel 03 Handwheel Components 04 Wheel 05 Wheel
2006-12-05 Mill Table
01 Mill Table 02 Mill Table
2007-01-17 Failed Mandrel
01 Failed Mandrel
2007-02-06 Cutter Rest
01 Cutter Rest Bottom 02 Cutter Rest Bottom 03 Cutter Rest Top 04 Cutter Rest Top
2007-02-06 Finishing Flywheel
01 Making Mandrel 02 Flywheel Fitted 03 Flywheel Fitted 04 Flywheel Turned 05 Flywheel Finished
2007-07-13 Low Profile Clamps T-Nuts
01 Clamped 02 Clamped 03 Clamped 04 Mill Rear 05 A Moment of Inattention
06 Replacement Gear 07 Finished Milling 08 Finished Milling 09 T-Nut Templates
2007-07-21 Low Profile Clamps T-Nuts
01 Counter Sink 02 Milling Foam 03 Power Tapping
2007-07-27 Main Support #3 Bush Take 1
01 Removing Collet Chuck 02 Bush (Part 3 - Main Support) 03 Bush (Part 3 - Main Support) 04 Bush (Part 3 - Main Support)
2007-07-28 Main Support #3 Bush Take 2
01 Main Support Bush
2007-08-02 Airway Flange #12 Part 1
01 Collet Chuck 02 Airway Flange #12 Elbow Part 1
2007-08-09 Airway Flange #12 Part 2
01 Airway Flange #12 Elbow Part 2 02 Airway Flange #12 Elbow
2007-08-11 Aluminium Casting
01 Furnace 02 Molds 03 Sand 04 Sand 05 Jack’s Shed
06 Jack’s Shed 07 Jack’s Shed 08 Jack’s Shed 09 Sand 10 Furnace
11 Pouring 12 Venting 13 Pouring 14 Pouring 15 Pouring
16 Pouring 17 Pouring 18 Pouring 19 Pouring 20 Cooling
21 Retrieving 22 Retrieving 23 Retrieving 24 Results
2007-08-24 Vice Mounting Clamps
01 Milling Height 17.5mm 02 Milling 2mm Step 03 Milling Ancor 5mm 04 Note Extra Clamps 05 Finished Milling and Drilling
06 Extra Clamps 07 Mounting Vice
2007-10-11 Hydraulic Knurling Tool Arms Part 1
01 Clamped Arms 02 Drill Pivot & Knurl Holes 03 Mill Relief 04 Mill Relief 05 Mill Relief
2007-10-11 Hydraulic Knurling Tool Arms Part 2
01 Drill Piston Drive Pilot Hole 02 Mill Piston Drive Hole & Relief 03 Clamping Arms 04 Drill Slot Holes 05 Mill Slots
2007-10-27 Hydraulic Knurling Tool Arms Finished
01 Finished